Hi all,
Trying to fight target burn before I make some footed arrows. I have used both oil and water poly and neither were good. My most recent arrows have a reverse capping of about 6 inches now of burned black smears from foam targets.
I see that people claim Massey Finish (cheap 5 minute epoxy thinned heavily with epoxy) eliminates target burn. However, people also say that it can be a pain to put on. I was wondering about a dip since it is so thin. That also got me wondering if it would work with a dip gasket?
Any thoughts or experience gratefully welcomed!
Anyone tried a gasket dipped Massey finish?
Moderator: Moderators
-
- Posts: 11
- Joined: Fri Oct 22, 2021 12:44 pm
- Stickbow Hunter
- Supporter
- Posts: 11637
- Joined: Sat Jul 26, 2003 8:33 pm
- Location: Maryborough Queensland
Re: Anyone tried a gasket dipped Massey finish?
I've never tried that so can't help with regards to using it. With 3Ds I have just used a silicon spray and give the arrows a wipe on the tip end after every couple of targets. It stops the target burn to large degree.
Jeff
Jeff
-
- Posts: 11
- Joined: Fri Oct 22, 2021 12:44 pm
Re: Anyone tried a gasket dipped Massey finish?
Maybe the poly I used is worse than normal, but I used a silicon target release (AAE I think?) and I got terrible burn on my first shot. ![Sad :(](./images/smilies/icon/sad.gif)
![Sad :(](./images/smilies/icon/sad.gif)
- Stickbow Hunter
- Supporter
- Posts: 11637
- Joined: Sat Jul 26, 2003 8:33 pm
- Location: Maryborough Queensland
Re: Anyone tried a gasket dipped Massey finish?
After doing my cap and cresting I just use a clear varnish and wipe on the full length of the arrow with a piece of rag. The varnish I have used was not water based. I hope you get it sorted so your footings keep on looking good.
Jeff
![Very Happy :D](./images/smilies/icon/biggrin.gif)
Jeff
-
- Posts: 11
- Joined: Fri Oct 22, 2021 12:44 pm
Re: Anyone tried a gasket dipped Massey finish?
My old arrows were water based poly. My new ones were first dyed bright red; doing more field and I wanted something more findable when I miss! Unfortunately the dye came right through the water based poly and cresting. Therefore I used an oil based spray for creating and then an oil based poly spray to avoid abrading the surface too much. I don’t think it was up to it. ![Sad :(](./images/smilies/icon/sad.gif)
Never mind, I like making stuff.
I’ll post a picture of my footings when I get them done.![Smile :)](./images/smilies/icon/smile.gif)
![Sad :(](./images/smilies/icon/sad.gif)
Never mind, I like making stuff.
I’ll post a picture of my footings when I get them done.
![Smile :)](./images/smilies/icon/smile.gif)
Re: Anyone tried a gasket dipped Massey finish?
Don't know about using a dip ghasket, but you've got to be quick using Massey finish. I wiped it on and only got one wipe in one direction before it got tacky.
Alan
-
- Posts: 11
- Joined: Fri Oct 22, 2021 12:44 pm
Re: Anyone tried a gasket dipped Massey finish?
Yeah, I searched the net pretty extensively and I couldn’t see reference to it. But it seems like it might work? Even if the “gasket” was a soaked cloth? Just have to move fast.
I might be better off learning to walk before I run though!
I might be better off learning to walk before I run though!